|
NetDominium SuperServer 6026TT-HIBQRF |
| Four hot-pluggable systems (nodes) in a 2U form factor. Each node supports the following: Dual Intel 5500 series Xeon Quad/Dual-Core, with QPI up to 6.4 GT/s Up to 48GB DDR3 1333/ 1066/ 800MHz ECC Registered DIMM / 24GB Unbuffered DIMM 1 (x16) PCI-E ( Low Profile) Integrated IPMI 2.0 with KVM and Dedicated LAN 5. Intel 82576 Dual-Port Gigabit Ethernet Controller 3x Hot-swap SATA Drive Bays 1400W Gold-level High-efficiency Redundant Power Supply Mellanox ConnectX QDR Infiniband 40Gbps Controller w/ QSFP connector |
|
|
| | | SYS-6026TT-HIBQRF | - SuperServer 6026TT-HIBQRF (Black)
|
| | |
| | | CPU | - Dual 1366-pin LGA Sockets
- Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below:
- Quad-Core Intel®
Xeon®Processor 5500 sequence (Nehalem-EP processor)
- NOTE: Support processors with Max TDP < 100W
| | QPI | |
| | |
| | | Memory Capacity | - 12x 240-pin DIMM sockets
- Supports up to 48 GB 1333 / 1066 / 800MHz DDR3 ECC Registered memory
- Supports up to 24 GB 1333 / 1066 / 800MHz DDR3 ECC Unbuffered memory
- Memory Mirroring supported
| | Memory Type | - 1333 / 1066 / 800MHz ECC Registered / ECC Unbuffered DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
| | DIMM Sizes | | | Memory Voltage | | | Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
|
| | |
| | | Infiniband | - Mellanox ConnectX QDR Infiniband 40Gbps Controller
| | Chipset | - Intel® 5500 (Tylersburg) chipset
- ICH10R + IOH-36D
| | SATA | - Intel ICH10R SATA 3.0Gbps Controller
- RAID 0, 1, 5, 10 support
| | IPMI | - Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
- Winbond® WPCM450 BMC
| | Network Controllers | - Intel® 82576 Dual-Port Gigabit Ethernet Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- Intel® I/OAT 3 support for fast, scaleable, and reliable networking
- VMDq support for better performance of virtualization
- 1x Realtek RTL8201N PHY (dedicated IPMI)
| | Graphics | | | Super I/O | | | Clock Generator | |
| | |
| | | Serial ATA | - Six Serial ATA ports
- 3 SATA hard drives supported
| | LAN | - 2x RJ45 LAN ports
- 1x RJ45 Dedicated IPMI LAN port
| | USB | - 2 rear + 1 header (2 Ports)
- 4 total USB ports, 2.0 Compliant / 1.1 Compliant
| | VGA | | | Serial Port | - 1 Fast UART 16550 serial port
| | Infiniband | - 1 External QSFP Infiniband Connector
|
| | |
| | | BIOS Type | - 32Mb SPI Flash EEPROM with AMI® BIOS
| | BIOS Features | - Plug and Play (PnP)
- PCI 2.2
- ACPI up to 3.0
- USB Keyboard support
|
| | | | |
| | | Height | 3.5" (89mm) | | Width | 17.2" (437mm) | | Depth | 28.5" (724mm) | | Gross Weight | 85 lbs (38.6kg) | | Available Colors | Black |
| | |
| | | Buttons | - Power On/Off button
- UID button
| | LEDs | - Power LED (on power button)
- Network activity LED
- System Overheat/fan fail/power fail/ LED
- UID LED (on UID button)
|
| | |
| | | PCI-Express | - 1 (x16) PCI-E ( Low Profile)
|
| | |
| | | Hot-swap | - 3x 3.5" SATA Hot-swap drive bays
|
| | |
| | | Redundant 1400W high-efficiency power supply with PMBus | | AC Input | - 1200W: 100 - 140V, 50 - 60Hz, 10.5 - 14.7 Amp
- 1400W: 180 - 240V, 50 - 60Hz, 7.2 - 9.5 Amp
| DC Output +5V standby | | DC Output +12V | - 100 Amp @ 100-140V
- 116 Amp @ 180-240V
|
| | |
| | | CPU | - Monitors for CPU Cores,+1.5V, +3.3V, +5V, +12V, +5 Stdby, +3.3 Stdby, VBAT, Memory Voltages.
- CPU Core 6-Phase-switching voltage regulator
| | FAN | - Total of four 4-pin PWM fans
- 4x fans with tachometer monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
| | Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 4x Fan Connectors
- PSU I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
- PECI
| | LED | - Power Fail / Overheat LED
- Suspend-state Indicator LED
- UID LED
| | Other Features | |
| | |
RoHS
| | | Environmental Spec. | - Operating Temperature: 10°to 35°C (50°to 95°F)
- Non-operating Temperature: -40°to 70°C (-40°to 158°F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
|
|
|
|